Application to purchase lines
A 4g lte router price moves when the site changes, even if the chassis drawing looks the same. Cabinet heat, antenna cable loss, SIM policy, and who commissions the unit all belong in the purchase note before factories are asked for numbers.
Request Factory QuotesAsk for the operating temperature window, ingress protection, and whether the test was run on the sealed enclosure. DIN-rail depth and a 12 V or 24 V feed are common, but write the voltage the cabinet actually has. GNSS or serial RS-232 to a controller is a separate line. Do not assume every industrial cellular router includes it.
The router may be a WAN backup, not the LAN switch. State port speed on the handoff, the VLAN, and whether failover is SIM-to-SIM or wired-to-cellular. Management method might be local CLI, SNMP, or a cloud seat with a license. License scope changes the 4g lte router price even when the metal box is unchanged.
Quantity may be high and the feature set small. Still record MIMO, antenna gain if an external antenna is required, and the connector. A short pigtail versus a 10 m run changes loss. Power over Ethernet from a nearby switch needs the class and the watt budget at the router.
| Stage | Document or constraint | Why it changes the buy |
|---|---|---|
| Survey | Bands in use, cable length, cabinet photo | Stops a datasheet peak from standing in for the link |
| RFQ | Quantity, destination, timing, optional budget | Gives factories one commercial basis |
| Quote review | Deviation column and accessory list | Keeps antennas and SIMs out of a hidden gap |
| Incoming | Model label versus accepted row | Catches a substituted revision before install |
Side A, category label: 3GPP TS 36.306 associates LTE UE Category 6 with a 301.5 Mbit/s downlink class and a 51.0 Mbit/s uplink class when the stated carrier-aggregation and MIMO conditions are met. Side B, site measurement: the same radio on one band, one MIMO layer, a narrow channel width, and a congested cell can land far below that class. Buyers should ask which conditions the datasheet uses, then decide whether the purchase needs that class or a lower category with a clearer band fit. LinkScope Sourcing 19 does not run the drive test, and a category label is not a substitute for receiver sensitivity at the planned frequency range.
A new unit can make warranty start and license entitlement easier to read. A refurbished unit can cover a legacy band set if condition, cycle history, and remaining support are written down. Mixing them in one average price hides the support path. Label each offer.
IEEE 802 describes Ethernet behavior at a standard level. It does not prove your host and this router pass traffic. FCC equipment authorization, when it applies, is per device. See the configuration cards and the brief.
Background: 80 kiosks, destination Arizona, antenna connector still unmarked, budget noted as USD per unit and not yet accepted by any seller. Process: the note lists 2x2 MIMO as a question, Power over Ethernet 802.3at as preferred, and asks each factory to state bands and whether the radio is locked to one carrier. Result: quotations that omit the lock status are parked, not averaged into a single 4g lte router price.
Name the cabinet, branch, kiosk, or sensor role, the host it connects to, and whether cellular is primary or backup. That sentence drives bands, ports, and power.
Hardware ship, configuration, antenna kit, and on-site commissioning can be separate. Ask which stages the factory includes and which stay with the integrator.
Write unknown next to temperature, cable loss, or SIM policy. An unknown is safer than a copied example from another city.
Send use, constraints, quantity, and destination together. The desk compares replies. It does not certify the installation.
Request Factory QuotesQUALIFIED BUYER SUPPORT
Compare factory quotations on one specification sheet
FREE basic specification and sourcing-requirements review
A sourcing benefit, when eligibility is confirmed, is limited to up to 3%
Eligibility applies to qualified business buyers and is confirmed after we review your product, quantity, destination, and sourcing requirements.