LinkScope Sourcing 19 industrial LTE router desk - Factory sourcing support for industrial 4g lte router cat6 300

Industrial 4G LTE Router Cat6 300

A US buyer who needs an industrial 4g lte router cat6 300 can start with the radio class, the Ethernet handoff, and the cabinet power path. LinkScope Sourcing 19 then asks factories to quote that same brief. The desk does not stock routers and does not treat a model family name as a measured throughput.

Interface cards that change a factory number

Leave a field blank when the site survey is unfinished. Mark it as an open question. A guessed band list or a guessed watt figure will make two quotations look comparable when they are not.

LTE category versus copper category

Ask whether the modem is a 3GPP LTE UE Category 6 class device. In the UE category definitions of 3GPP TS 36.306, Category 6 is associated with a 301.5 Mbit/s downlink class and a 51.0 Mbit/s uplink class under stated MIMO and carrier-aggregation conditions, which buyers often shorten to a 300 Mbit/s class. Separately ask whether the LAN plant is Category 6 copper with a channel length near 100 m. Those two uses of “Cat6” are different lines on a bill of materials. The standard names a class. It does not measure this cabinet.

Port count and port speed

State how many LAN ports you need and whether each port is 10/100 or 10/100/1000. If a WAN port is dedicated, say so. Switching capacity is a switch question; on a router it still matters when several LAN devices share one cellular uplink.

Power input

Separate a 12 V, 24 V, or 48 V DIN-rail feed from 802.3af, 802.3at, or 802.3bt Power over Ethernet. Ask for the watt budget at the router, the connector type, and whether ignition sense or a wide input range is required.

Evidence on the exact item

Request the current datasheet, the supported band table, receiver sensitivity, transmit power, antenna interface, and any FCC equipment authorization file that names the exact model. IEEE 802 Ethernet overviews and 47 CFR Part 2 Subpart J are question sources for port behavior and authorization scope. They do not certify the unit you have not yet named. If several LAN devices share the cellular uplink, also ask whether a forwarding rate or switching capacity figure is even defined for that chassis.

Buyer roles that usually split the brief

Telecom procurement manager

Holds quantity, US destination, Incoterm preference, and the optional target budget with currency and per-unit or whole-order basis. Typical open items are software or license scope and whether a high-end, mid-range, budget-friendly, or undecided supplier stance should be written into the note. That stance is a preference, not a verified rating.

Network engineer

Owns frequency range, MIMO, channel width assumptions, SIM or eSIM policy, and routing or security features such as IPsec, firewall rules, and management VLAN. A 300 Mbit/s class title is not a test record under a stated carrier, MIMO layer count, and traffic mix.

Field deployment team

Sees DIN-rail space, ingress protection, antenna cable loss, and the cabinet temperature. Ask for the operating range and whether the figure was measured at the enclosure skin or at the modem. LinkScope Sourcing 19 does not audit the cabinet.

RFQ questions before a factory email

What should the buyer prepare?

Product family, application, LTE bands, antenna connector, port count, port speed, power method, quantity, US destination, and requested timing. Add serial, DI/DO, or GNSS when the host actually uses them. The longer checklist sits in the procurement brief.

How does independent supplier matching work?

LinkScope Sourcing 19 reads the note, asks factories to answer the same sheet, and lines up deviations. It is an independent sourcing partner. It does not claim factory ownership or authorized distributor status, and it does not publish a savings percentage.

Which costs stay outside the chassis price?

Antennas, pigtails, SIM service, licenses, spare power supplies, freight, duties, and commissioning. Compare those lines after the radio configuration matches. A headline lte router price without those lines is not a total procurement scope.

What evidence is tied to the proposed model?

Current datasheet, band and MIMO table, power draw, ingress protection test basis, and applicable FCC equipment authorization for that model. A family brochure does not transfer those rows. See the inquiry configurations or send the brief.

Paste the multi-line router sheet

Write the modem class, the Ethernet ports, the antenna interface, the power input, the quantity, and the destination in one note. Factories can then mark compliant, deviation, or alternative on each line. LinkScope Sourcing 19 compares those replies. It does not upload a file store and it does not hold inventory.

Optional budget: amount or range, currency, and whether the figure is per unit or for the whole order. No live quotation is required to start.